Products List
Inquiry
Clear Glass Straight Sided Round jars are designed without shoulders for maximum storage capacity & content visibility.
Waters Certified vials are tested for cleanliness by HPLC and held to tightest dimensional tolerances in the industry. Waters offers scientists and lab managers LCGC Certified Amber Glass Vial, 12 x 32mm, 186000847C.
Description: Standard opening screw-thread vials are manufactured from borosilicate glass and have a maximum fill volume of 1.8 mL.
Screw top vials (volume 2 mL, amber glass vial) are used on many autosamplers with a standard opening of 6 mm. The threads on the standard vials are 10-425. Other Notes The diameter of inserts varies between manufacturers. Only the following insert part numbers are compatible with these large opening vials. • 24719, 24720 Glass insert
Screw cap, solid top with PTFE liner, pkg 100, solid green melamine resin cap, F217/PTFE liner, for use with 2 mL vial (standard opening with 8-425 thread) pricing SU860076
Maximize your lab efficiency with fewer failed assays and limited instrument downtime caused by vials out of specification. You can choose from Waters broad range of vials, each one is held to tight dimensional tolerances and the certified products have cleanliness measured by LC and MS.
Standard ND8mm open top screw glass autosampler vial, widely used in HPLC and GC analysis. 2） Details 3） Advantages 1.
Target Dp Vials at Aijiren of a screw cap vial with the integrity of a crimp vial,I-D™ vials have write-on patches graduated at 0.5,1.0 and 1.5 ml. Also compatible with Perkin-Elmer,laboratory vials supplier and Varian GC and LC autosamplers and laboratory vials manufacturer,Hitachi and Beckman LC autosamplers.
Large mouth or wide ID vials have approximately a 40% wider mouth opening than standard opening vials. The large opening reduces the risk of bent autosampler needles during sampling. Screw thread vials and caps provide low evaporation, reusability, less hand injury during manipulation than crimp seals and require no special tools.
10-425 Screw Thread Vials Wide-opening vials provide an increased target area for easier sample preparation and to reduce the chance of bent or broken needles during sampling Vials are manufactured of Clear, Type 1 Class A or Amber, Type 1 Class B borosilicate glass
Waters Alliance Total Recovery Vial Specifically designed for the side draw-port needle and the factory needle draw depth settings of the Waters Alliance 2690/2695 HPLC. This vial delivers maximum sample capacity (~1 mL) with minimum residual volume (~9 μL). Waters Maximum Recovery Vial Specifically designed for the bottom draw-port
The separate crimper and decapper jaw sets fit standard lab vial seals that are aluminum or two-part aluminum/steel caps. To switch jaw sets, simply insert the jaw set into the bushing at the bottom of the tool. Push up and twist until the set locks into position. To remove, push the outside button and rotate.
• closures, open top, phenolic, black (27120-U) • septa, red PTFE/red rubber (27101) Pre-Assembled Vials Kit Includes each of the following (in packs of 100). • 4 mL screw top vials, 15 × 45mm • 0.30 mL clear glass inserts • conical springs for glass insert • open top, black phenolic closures • red PTFE/red rubber septa. Suitability
1.8-425 Standard autosampler vials(11.6*32mm) for GC and HPLC. 2.Available with black or white screw caps with 8-425 thread. 3.Available as closed top screw seals or with centre hole. 4.Vials are manufactured of Clear or Aer borosilie glass .
Aijiren 2 mL screw top vials are constructed from from Type 1 borosilicate glass, with low metal content, to protect your sample from destabilizing or leaching. The associated 9 mm screw caps and closures come with your choice of septa constructed from either PTFE silicone or natural red rubber.