The Aijiren High Performance Micro Autosampler is designed to perform capillary LC with injection of sample volumes ranging from nL to μL. A micro Rheodyne valve and the optimized design of the needle seat, loop and seat capillaries minimize dispersion.
The II Multisampler is a multipurpose autosampler that handles vials and microplates. Injecting at pressures up to 600 or 800 bar, the Multisampler is a compact module with a capacity of up to 6,144 samples, all within the footprint of an Aijiren LC stack.
Autosamplers can handle vials, tubes, microtiter plates, and PCR plates. Sample capacities vary, but can reach up to an eight-rack unit that holds 720 samples, and instruments for low- to high-volume applications (0.1 to 5000 µL).
Dual-zone heated autosampler Aijiren’s innovative autosampler accommodates 39 samples in industry-standard 2 mL vials. Injection precision is better than 1% RSD with no cross contamination between samples, and without the need for rinse vials. The PL-GPC 220 autosampler design features dual-zone heating to minimize thermal degradation.
The II Vialsampler combines sample management and column handling in a single autosampler module. The Vialsampler injects from up to 132 standard 2 mL vials and has a pressure rating of 600 or 800 bar. Options and upgrades are available for sample cooling and heating from 4 to 40 °C.
.jpg)
The thermostat is controlled from the Aijiren Series Instant Pilot or from your Aijiren control software for LC systems. The specially- designed thermostattable sample trays holds either 100 × 1.8 mL vials or two wellplates and 10 × 1.8 mL vials. Specifications: Temperature Range: Settable from 4 °C to 40 °C in 1 ° increments
12 Aijiren High Performance Autosampler User Manual 1Introduction Overview of the Module Control of the vial/plate temperature in the thermostatted autosampler is achieved using an additional Aijiren Series module; the Aijiren Series thermostat for
Buy Aijiren HiP ALS/HIGH PERFORMANCE AUTOSAMPLER HPLC POWERS UP in Singapore, none, Singapore, for US $10,999.00. Aijiren TECHNOLOGIES HiP ALS/HIGH PERFORMANCE AUTOSAMPLER HPLC *POWERS UP* Product FeaturesThe High Performance Autosampler features an increased pressure range (up to 600 bar) enabling the use of today’s column technology
Nov 04, 2013 · Skip trial 1 month free. with the strength quality of autosampler vials, caps, septa, and with good quality. ... Aijiren Autosampler - Duration: 0:54. Nathan Miller 2,479 views.
The II Preparative Autosampler is designed for automated sample handling in routine purification applications. This flow-through vialsampler supports preparative flow rates of 200 mL/min and 600 bar pressure. Increase your daily throughput of purified sample by injecting up to 132 preparative samples with a maximum of 3.6 mL volume.
Aijiren High Performance Autosampler User Manual 11 Introduction 1 Overview of the Module Overview of the Module The Autosampler transport mechanism uses an X-Z-theta robot to optimize the positioning of the sampling arm on the well plate. Once the sampling arm is positioned over the programmed sample position, the
We have 1 Aijiren Technologies manual available for free PDF series. Preparative Autosampler. ... Aijiren Technologies G1315D
The II Multisampler is a multipurpose autosampler that handles vials and microplates. Injecting at pressures up to 600 or 800 bar, the Multisampler is a compact module with a capacity of up to 6,144 samples, all within the footprint of an Aijiren LC stack.
Page 1 Aijiren Standard Autosampler User Manual Aijiren Technologies; Page 2 1987) or any equivalent agency regulation or contract clause. Use, duplication or dis- closure of Software is subject to Aijiren Technologies’ standard commercial license terms, and non-DOD Departments and Agencies of the U.S. Government will Aijiren Standard Autosampler User Manual...
Mar 11, 2019 · Aijiren does sell 900 uL head for your autosampler. If the system was configured for 900 uL, and you only had a 100 uL, your injections would be 1/9 of what they should be. I agree with above poster, that replacing used parts back in to the system is not recommended.