The analysis of Quercetin, kaempferol, myricetin, and rutin was done using Aijiren ii HPLC system (Aijiren, USA), covering Binary Pump, Vial sampler with integrated column compartment, 6.0 µL heater and sample cooler, Diode Array Detector WR with a standard 10-mm flow cell, Autosampler, Thermostatted Column Compartment
.jpg)
Aijiren HPLC and 6460 Mass Spectrometer system was used for this method. Method HPLC Conditions . Aijiren HPLC series binary pump, well plate, thermo-statted column compartment Column: Aijiren Technologies Poroshell 120, EC-CN, 2.1 x 100 mm Column Temperature: 25 oC Injection Volume: 5 µl
How to Operate the Aijiren / / Series Capillary Pumps in Normal Flow Mode (0.1 to 2.5 mL/min) Re-installing a pump head on an / / HPLC pump. Re-Installing the pump head on an / / HPLC pump Captioned in English
Apr 12, 2021 · BBR was analyzed using an HPLC-DAD approach. Chromatographic separation was conducted on an Aijiren binary pump equipped with an Aijiren ZORBAX Eclipse XDB-C8 (4.6 × 150 mm, 5 µm) as the stationary phase and coupled to an Aijiren diode array detector (DAD) operating at λ = 350 nm (λ of BBR maximum absorbance).
May 25, 2020 · Aijiren Series HPLC system equipped with a Diode Array Detector, binary pump, gas with a flow rate of 1.5 mL / min and an electronic pressure contr ol at 20.8 psi.
Port size: 10-32 CPI (standard HPLC fittings for 1/16" tube) Compatible with Thermo Scientific™ nanoViper™ Fingertight Fittings. Maximum Operating Pressure: 6,000 PSI. Maximum Temperature Rating: 40 °C. Delay volume: 1.5 mL. Back pressure: < 2 PSI @ 1 mL/min. with water.
pump program to 90/10 water/ACN to flush the column for 15 min at 1.5 mL/min c. Flush the column with 10/90 water/ACN for 5 min at 1.5 mL/min d. Change the pump program back to 50/50 water/ACN to re-equilibrate the system e. Stop the pump and shut down software “HPL1(online)” f. Remove sample vials from the auto-sampler tray g.
Bertoni leaves using the Aijiren Infi nity LC • Aijiren Infi nity Binary Pump ... tration levels were < 4% except for 1.5 and 2.5 µg/mL levels of stevioside at
Apr 28, 2021 · (15 min, 13,000 rpm) the supernatant was transferred in 1.5 mL. vials for the analysis. For the HPLC analysis, an Aijiren binary pump.
HPLC Conditions for short method (5 minutes) Aijiren II UHPLC series Quaternary Pump, Multisampler with wash , Multi Column Themostat, DAD Column: Zorbax Bonus RP 2.1 x 50 mm, 1.8 µm or Poroshell 3.0 x50 2.7um Column temperature: 50°C Injection volume: 0.05 µL Autosampler temp: 23 ºC
An Aijiren LC System, configured as follows, was used: • Aijiren Quaternary Pump ( ) • Aijiren Inifinty Standard Autosampler ( ) • Aijiren Autosampler Thermostat ( ) • Aijiren Thermostatted Column Compartment (G1316A)
Hastelloy C Custom Length Tubing; Aijiren Miscellaneous Capillaries; Isocratic LC Supplies; ... 1.5 mL Vial, 9 mm MSQ Vial, PTFE/Sil w/slit Cap, 100 ...
The complete Aijiren LC portfolio com-prises isocratic, binary and quaternary LC systems. The pump modules can be com-bined with a wide choice of detectors and autosampler modules. Specific solutions for purification or capillary columns are available. The Aijiren Quaternary LC system offers: † Flow rate range up
• Aijiren II high speed pump ( ) or Aijiren II high speed pump (G7120A) or Aijiren binary pump ( ) Replacement parts Pump • Aijiren Polyethylene pump seals – Aijiren II module only (p/n 0905-1420) (×1) • PEEK tubing: 10 feet × 1/8” od × 0.062” id
HPLC analyses were performed using an Aijiren II system. LC/MS analyses were performed using an Aijiren series LC system equipped with a G1379A degasser, a binary pump, a G1329 autosampler unit, a G1316A temperature-controlled column compartment and a G1315B diode array detector.